Open your pentair pool filter pump parts and take a look inside. Reconnect the plumbing to the multiport valve.
After all the sand has been removed reach in the filter and fold the laterals up into a 90 degree and remove the lateral assembly.
How to change sand in pentair pool filter. This document is subject to change without notice. If you find any damage, replace the damaged parts at once. Turn on the system to allow the new sand/gravel to be cleaned.
I have talked to a few people and they said just fill them with new pool filter sand 20 silica. Of sand you can’t just shimmy the filter to gain access or move the filter to repair a pipe fracture. Some of our viewers wonder how often the sand should be changed in a sand filter, so the pool guy answers those questions.
They contain over 1000 lbs. If there is no damage, consider cleaning or replacing the filter cartridge or. It is a good idea to backwash and rinse the filter for a few minutes to remove the sand dust before you begin normal filtering.
Additionally, the design maximizes run times between cleanings saving you time and effort! How to change pool filter sand. First things first, reduce the weight of the filter.
Our swimming pool sand filters feature a special internal design that maintains the sand bed level and ensures even water flow for the most efficient filtration possible. There isn’t a set amount of time needed to complete this step. Tape off the top of the filter pipe with duct tape so that sand will not be inserted in the laterals, clogging your filter.
Remove inner grids and check for any damage. Switch off the pump motor at the power supply. Follow the process below to replace the sand in your filter.
This sand is made from quartz, making the edges of the grains of sand perfect for trapping the contaminants. This will be done in one of three ways: Visit www.pentairpool.com and staritepool.com © 2009 pentair water pool and spa, inc.
It usually takes no more than a few minutes. Go to our guide on how to replace the sand in a pentair triton 2 side valve sand filter for further information. Firstly, set the multiport valve to backwash.
In some cases, it may be due to excessive sand or diatomaceous earth present in the filter. To drain it manually, lay plastic sheeting underneath the filter drain assembly, remove the assembly and turn on the pump. Definitely one of the most common of three filter sands is silica sand.
It’s too big and too heavy to move, how do you solve the problem? Move the multiport valve position on the filter to backwash. I am getting ready to change out the sand in a couple commercial sand filters ( pentair triton ii 140, 100) and am looking for a bit more info.
Run the pump for a few minutes to backwash the new sand to remove any fine sand particles. The water should be a dark brown at first, then change to a. Connect the hose to the skimmer inlet.
Sand filter installation and user’s guide technical support sanford, north carolina (8 a.m. Completely switch off the pump and timer. Replace any broken parts if necessary.
Sand / dust in the pool: Install the sand guide in the top of the filter and fill the tank about half full of water. This is a common problem and might be a sign of outside debris being blown into the pool and not being filtered out by the filter cartridge, or filter media (sand or de) being flushed back into the pool.
Otherwise, these fine particles may escape through your filter into the return lines and deposit in your pool. Use the shop vac or a bucket to remove the old sand from your filter. Silica sand doesn’t have an “extra feature” like how glass sand minimizes channeling.
At pentair, our pool sand filters are easy to operate and maintain. You can also order any pentair pool filter parts © 2010 pentair water pool and spa, inc.
#20 silica sand to be exact. Steps for changing the sand in a sand pool filter: Pour the sand into the top of the filter at a slow
You don’t want the pump to automatically start when you have the filter disconnected from the water pipes. When you are ready, turn the pump off again and change the multiport valve setting to “filter” and turn the pool pump back on. For this example, i’m talking specifically about the pentair tr 140 c sand filter.
Before pouring the sand into the filter, look inside and check the lower under drain for broken or loose laterals (or fingers), which may have been accidentally damaged by rough handling during shipment. Check the filter cartridge for damage. One filter calls for 650lb sand 275 pea gravel, the other 450lb sand 150 pea gravel.
Et) moorpark, california (8 a.m.