Take out the old washer and then install a different one. Then put the closed end of a wrench (if possible) over the bonnet nut, which is the 6 sided thing that screws into the valve body.
When attaching the new valve, make sure to tighten it well so that once you have turned back on the water.
How to replace toilet shut off valve handle. Unscrew the packing nut with a wrench. This nut is located under the handle of the valve. Shutting off your main water supply valve.
A nut holds the toilet handle in place. I removed the valve handle to find that even the piece connected to the handle was plastic. Here’s how to locate it:
I would like to replace this shutoff valve with another one (not plastic this time). Use a wrench to remove the nut. The packing washers and thrust washers will fall.
I doubt if age has anything to do it, more likely a hack handyman or a ignorant homeowner. The first thing you should do is to find the main shutoff valve. In case your toilet doesn’t have a valve, then turn off the main water supply.
You can do it with your hand or with a meter wrench. When you close the main shut off valve, there will be still some pressure in the water system. Inside of the chrome cover has groves to fit around the clamp.
Turn the nut in the clockwise direction. If this doesn’t stop the leakage, proceed by loosening the packing nut by turning the nut in the counterclockwise direction with a plier or wrench. Unscrew the valve stem with your fingers.
I tried using a wrench to grip the plastic and turn it tighter, but can't get too crazy or i will just destroy the plastic. Chrome cover is held in place with a screw into the end of the stem. Replace a leaky toilet water shut off valve.
If it’s a round handle, keep turning it clockwise until it stops. Close the shut off valve; Turn on the water to test if the valve still leaks.
Part one was the chrome cover part, part two was a small clamp the is held in place around the stem with two small screws. To shut the water supply off the house entirely, turn the lever clockwise to make it perpendicular to the pipe. If this doesn’t solve the problem, turn the water back off and examine the fitting for damage.
Disconnect the supply lines from the value. Check out these 4 simple steps on how you can replace a washer; Install the supply line (s) connecting the valve (s) to the faucet (s).
Unscrew the valve stem a bit to ensure the washer isn't tight against the seat. Turn off the house water main before taking apart the toilet shutoff valve. Properly sized replacement washers for the shutoff valve are available from plumbing supply houses and better hardware stores that stock a large inventory of repair parts.
Doing so will avoid water wastage or even a flood. If this step doesn't stop the leak, you'll need to replace the whole valve. Discard the handle of the shutoff valve.
This is the most basic repair to ensure that the nut is properly tightened. Sometimes the bonnet nuts on valves can be on awfully tight (but it. Turn the water back on at the main and check the new valves for leaks.
If for some reason you were to torque on the shutoff valve, slip and fall against it, or hit it with a tool, it is always safe to shut the water off. Use the pliers to firmly grip the packing nut. Remove the screw and the knob and when you have the new knob, loosen the bonnet nut, the large nut just behind the knob, 1/2 turn, install the replacement knob and gently rotate each way until you have loosened the valve.
There's little question that you should have a shut off valve on the toilet supply. Ensure it matches the size of the one you removed. Unscrew the valve and replace it.
If you see any seepage, tighten the connection a little more. Loosen the nut from inside of the tank using an adjustable wrench if necessary. Only repair or replace the toilet when the water supply is completely turned off.
Considering we do not know exactly what the problem is that you are dealing with, it would be best if you turned the water off to the supply to the toilet. This is really rocket science, just get the materials needed, and shut the water off. This means you will turn the nut clockwise to loosen.
Complete installation instruction on how to replace a straight or angle water shut off valve.if the water won't.