Replace it with the cartridge filter you took out in the previous step. Here’s how to do it:
Turn the power off at the isolator or the mcb in the house (the system is pressurised do not remove the filter while the power is still on).
How to turn on a hot tub filter. This lid is often large and round or rectangle on the top wall of your hot tub. Remove the filter from the hot tub. The best way to do this is by flipping the circuit breaker switch that leads to your hot tub.
Turn off your hot tub at the isolator switch. Then clean them and let them dry. While the filters are out of the spa and the power is still off, check the filter bay for debris (leaves etc) that could be causing a blockage.
Now the spa should be good for use and remember the process for when you replace the filter again in 12 months. As the water flows through the filter, any debris particles and contaminants in the water get blocked out. In this informative video we teach you how to quickly and easily replace the filter on your pdc spas hot tub.
Alternate between the low and high setting for about an hour. Turn off the hot tub. They also prevent this debris from getting into the pump and heater which would otherwise have the potential to cause damage and reduce its lifespan.
Completely remove filter or filters from the hot tub. Wipe down the underside of your hot tub cover and filter hole in the tub wall with a hot tub cleaner. Now it’s time to turn the tub on.
Your filter should be rinsed regularly, about twice a week, based on your hot tub usage and climate. Use a hose pipe with good water pressure to remove the larger debris from the pleat It would be best if you run it in two intervals of four hours.
Then turn off the jets. Once the power is cut, the best tool to help remove a stuck filter will be a strap wrench. Clean it repair the hot tub filters.
These particles will also be picked up by the filtration system of your hot tub. This not only keeps you safe, but also keeps any debris from becoming accidentally pushed into your hot tub’s pump if for some reason it decides to begin the clean cycle before you have time to insert a filter. When you turn on the system, it causes water to circulate throughout the hot tub.
Turn the hot tub back on at the gfci breaker, but leave the filters out of. Next, turn the jets on the “low” setting and let them run for 10 to 20 seconds. After turning on the jets on high, switch it to a low setting and let the jets run too.
For pressurised filtration systems (most coast spas, hydropool 1. Turn the power to the hot tub off. So, before you go about changing your filter, it’s best to turn offer power to your hot tub.
Finally, up the jets to the “high” setting, and run them for an additional 10 to 20 seconds. Allow the water to cycle through the system for a few hours in order for the system to acclimate. It’s important that your hot tub pump is not running while you’re cleaning the filter.
Using the control pad, turn off the spa or put the spa in “hold” mode. Regular shock treatment is recommended. Running the filter will help your hot tub have adequate maintenance and remove any contaminants before they get to make your water dirty and unhealthy.
With the tub filled up, you can turn off the hose and remove it from the filter well. Use a strap wrench to create a lever that will help remove the filter. That is what makes the filtration system so important to it.
Give your filter a quick rinse to remove large debris. Then you have nice clean water return to the spa area. It’s best to have an electrician hook it up to a dedicated breaker so it doesn’t overload your electrical grid.
It should be enough to run your hot tub filter for up to eight hours a day. Keep the pump going 24 hours a day. Many hot tub filter housings look different so find which housing is yours here.
Drain the water from your hot tub (if necessary) by cutting off the power, the water will stop getting sucked into the filter and it will make it easier to remove. Switch off the hot tub and remove the filters. If the filters are damaged, you should repair or replace them.
Usually your lid will have cup holders designed neatly into the lid. Spray the surface of the filter with happy hot tubs instant filter cleaner thoroughly to impregnate the filter, wear protective clothing (gloves and eye protection etc.) Repeat this process 2 or 3 times.
Start by putting the tub in priming mode using your spa’s control panel. Maintain the hot tub's filter. Drain the water from your hot tub (if necessary) by cutting off the power, the water will stop getting sucked into the filter and it will make it easier to remove.
Turn off the hot tub at the gfci breaker. How you remove the filter cartridge will depend on what type of filtration the hot tub has. Replace the water that was removed from the hot tub and power the spa up.
As you'll see, it's an important part in maint. Turn the hot tub on. Use a strap wrench to create a lever that will help remove the filter;
Clean water is essential to have in a hot tub. Wet filters will begin to work more quickly than dry ones once installed. Turn the power to the hot tub off ;
Often the filter housing is on the corner. Make sure power to your hot tub is turned off to prevent electrocution and accidental damage to the pump by running it dry. If the filters were working or clean, then you wouldn’t have as much scum.
Once the tub has power, turn it on. Remove the hot tub filters and place them in the bottom of the tub to absorb water while it fills. If you’re not sure where your hot tub filter is, consult the hot tub’s user manual.
Generally speaking, the rule of thumb is to thoroughly clean your filter once every two weeks with a filter cleaner that will allow you to clean between the. Here at outdoor living online we’ve put together a step by step guide for cleaning you hot tub filter: